Communicate with Supplier? Supplier
Dartin Xin Mr. Dartin Xin
What can I do for you?
Chat Now Contact Supplier
Storm Circuit Technology Ltd

Enepig Plating Specification - manufacturer, factory, supplier from China

(Total 22 Products for Enepig Plating Specification)

  • Edge plating ENEPIG pcb process

    Edge plating ENEPIG pcb process

    • Model No.: Storm-0373

    • Transportation: Ocean,Land,Air

    A 48 hour salt spray test was performed on the gold finger after 500 times of plug test to evaluate the corrosion resistance of the gold finger of the two processes Test conditions salt solution composition 50g L NaCl solution test temperature 35 pressure barrel temperature 47 pH value 6 5 7 2 25 placement angle the...

    Contact Now

  • ENEPIG pcb surface finish for wire bonding

    ENEPIG pcb surface finish for wire bonding

    • Model No.: Storm-0376

    • Transportation: Ocean,Land,Air

    ENEPIG gold finger has good resistance to plugging corrosion and aging and its performance is similar to that of electroplated hard gold ENEPIG gold finger has good resistance to plugging corrosion and aging Similar in hard gold PCB features 1 Layer 2 2 Material FR4 3 Thickness 1 2mm 4 Copper 1OZ 5 Mini hole 0 15mm 7...

    Contact Now

  • PCB hard gold and ENEPIG PCB

    PCB hard gold and ENEPIG PCB

    • Model No.: Storm-0375

    • Transportation: Ocean,Land,Air

    ENEPIG thick palladium thin gold has good solderability full tin and IMC is uniform and continuous ENEPIG thick palladium thin gold has good solderability full tin and IMC is even and continuous PCB features 1 Layer 2 2 Material FR4 3 Thickness 1 6mm 4 Copper 1OZ 5 Mini hole 0 15mm 7 Mini width space 0 1mm 0 1mm 8...

    Contact Now

  • ENEPIG solder joint reliability

    ENEPIG solder joint reliability

    • Model No.: Storm-0374

    • Transportation: Ocean,Land,Air

    When NEPIG gold finger technology is applied to bonding products the production process is simple the gold finger is four bread gold and the bonding pad spacing is strong the cost is lower than the traditional electroplated hard gold finger technology PCB features 1 Layer 2 2 Material FR4 3 Thickness 1 6mm 4 Copper...

    Contact Now

  • electroless copper ENEPIG  plating pcb

    electroless copper ENEPIG plating pcb

    • Model No.: Storm-0372

    • Transportation: Ocean,Land,Air

    After the plug test there is a light silver gray trace on the gold surface of the electroplated hard gold finger The elemental analysis results are Au Ni where the atomic percentage of Au is 94 99 The gray scratched surface is Au The contact resistances before and after the plug in test are 6 26 and 5 59 m and the...

    Contact Now

  • 4 layer Rigid-flex  PCB with ENEPIG

    4 layer Rigid-flex PCB with ENEPIG

    • Model No.: Storm-0363

    • Transportation: Ocean,Land,Air

    What is ENEPIG ENEPIG Electroless Nickel Electroless Palladium Immersion Gold is a surface finish for Printed Circuit Boards ENEPIG works well with lead free and conventional eutectic solder alloys This is the best way for gold wire bonding Advantages for ENEPIG PCB features 1 Layer 4 2 Material FR4 Polyimide 3...

    Contact Now

  • ENEPIG PCB and Rogers material

    ENEPIG PCB and Rogers material

    • Model No.: Storm-0365

    • Transportation: Ocean,Land,Air

    Chemical nickel palladium ENEPIG is one of the common surface treatment processes for PCBs but in recent years the ENEPIG process has been applied to gold fingers in wire bonding optical module product We make many 4 layer ENEPIG PCBs with competitive price PCB features 1 Layer 4 2 Material FR4 3 Thickness 1 2mm 4...

    Contact Now

  • Ipc-4556 specification for ENEPIG

    Ipc-4556 specification for ENEPIG

    • Model No.: Storm-0367

    • Transportation: Ocean,Land,Air

    Small form pluggable boards SFP boards for short in the industry are mainly used for optical modules converting electrical signals into optical signals in communication equipment The following features 1 Gold fingers PCB are long or short gold fingers or segmented gold fingers 2 Gold fingers need to be plated with...

    Contact Now

  • IPC standard for ENEPIG

    IPC standard for ENEPIG

    • Model No.: Storm-0370

    • Transportation: Ocean,Land,Air

    Use the plug connector to plug and unplug the thick palladium thin gold and electroplated hard gold fingers and manually insert and remove 500 times Observe the appearance of golden fingers with a stereo microscope After the plug test there is a silver gray trace on the gold surface of the thick palladium thin gold...

    Contact Now

  • 2 layer ENEPIG PCB with green  solder

    2 layer ENEPIG PCB with green solder

    • Model No.: Storm-0368

    • Transportation: Ocean,Land,Air

    Thick palladium and thin gold The thickness of the coatings of ENEPIG gold fingers and electrical hard gold fingers are measured by the X ray coating thickness gauge as shown in Table 1 Au 0 061 m Pd 0 347 m hard gold process Au 0 388 m PCB features 1 Layer 4 2 Material FR4 3 Thickness 1 6mm 4 Copper 1OZ 5 Mini hole 0...

    Contact Now

  • ENEPIG finishing plating  thickness

    ENEPIG finishing plating thickness

    • Model No.: Storm-0371

    • Transportation: Ocean,Land,Air

    Metal palladium is a platinum based element with stable chemical properties and acid and oxidation resistance At the same time the hardness of metal palladium is greater than that of hard gold PCB including cobalt and it has better resistance to plugging and unplugging The chemical nickel palladium gold process...

    Contact Now

  • 2 layer ENEPIG PCB with red solder mask

    2 layer ENEPIG PCB with red solder mask

    • Model No.: Storm-0366

    • Transportation: Ocean,Land,Air

    Chemical nickel palladium gold ENEPIG is a common type of surface treatment Unlike traditional chemical nickel gold surface treatment processes a layer of palladium is introduced between the nickel layer and the gold layer which can effectively prevent the migration of nickel to the gold layer Therefore it has good...

    Contact Now

  • ENEPIG PCB with high frequency

    ENEPIG PCB with high frequency

    • Model No.: Storm-0364

    • Transportation: Ocean,Land,Air

    The ENEPIG finish process does not need to connect the wire bar and has good uniformity in the process of wiring the chemical nickel layer is the main base so the tensile test of the hardness of the nickel layer to the support and bonding strength of the wire will It is influential and the nickel layer in the chemical...

    Contact Now

  • Metal core PCB specification

    Metal core PCB specification

    • Min. Order: 1 Bag/Bags

    • Model No.: Storm-0360

    • Transportation: Ocean,Land,Air

    Thermal expansion and contraction are the common nature of materials and the thermal expansion coefficients of different materials are different The aluminum based printed board can effectively solve the problem of heat dissipation thereby alleviating the problems of thermal expansion and contraction of different...

    Contact Now

  • 2 layer pcb edge plating board

    2 layer pcb edge plating board

    • Model No.: Storm-0298

    • Transportation: Air

    PCB features 1 Layer 2 2 Material FR4 3 Thickness 1 6mm 4 Copper 1OZ 5 Mini hole 0 25mm 7 Mini width space 0 2mm 0 2mm 8 Finish Immersion Gold Our manufacturing capability Manufacture capability layers 1 32 layers Materials CEM1 CEM3 Teflon Rogers FR 4 high TG FR 4 aluminum base halogen free Max board Size 510 1200mm...

    Contact Now

  • express RO4350B ENEPIG PCB

    express RO4350B ENEPIG PCB

    • Model No.: Storm-0191

    • Transportation: Ocean,Land,Air

    PCB features 1 Layer 3 2 Material Rogers 3 Thickness 0 8mm 4 Copper 1OZ 5 Mini hole 0 25mm 7 Mini width space 0 15mm 0 15mm 8 Finish ENEPIG Our manufacturing capability Manufacture capability layers 1 32 layers Materials CEM1 CEM3 Teflon Rogers FR 4 high TG FR 4 aluminum base halogen free Max board Size 510 1200mm...

    Contact Now

  • 4 layer 1.6mm ENEPIG  PCB

    4 layer 1.6mm ENEPIG PCB

    • Model No.: Storm-0294

    • Transportation: Ocean,Land,Air

    PCB features 1 Layer 4 2 Material FR4 3 Thickness 1 6mm 4 Copper 2OZ 5 Mini hole 0 15mm 7 Mini width space 0 2mm 0 2mm 8 Finish ENEPIG Our manufacturing capability Manufacture capability layers 1 32 layers Materials CEM1 CEM3 Teflon Rogers FR 4 high TG FR 4 aluminum base halogen free Max board Size 510 1200mm Material...

    Contact Now

  • 4 layer Green Solder ENEPIG surface finishing

    4 layer Green Solder ENEPIG surface finishing

    • Model No.: Storm-0279

    • Transportation: Ocean,Land,Air

    PCB features 1 Layer 4 2 Material FR4 3 Thickness 1 6mm 4 Copper 1OZ 5 Mini hole 0 15mm 7 Mini width space 0 2mm 0 2mm 8 Finish Immersion Gold Our manufacturing capability Manufacture capability layers 1 32 layers Materials CEM1 CEM3 Teflon Rogers FR 4 high TG FR 4 aluminum base halogen free Max board Size 510 1200mm...

    Contact Now

  • 2 layer 0.2mm  ENEPIG PCB

    2 layer 0.2mm ENEPIG PCB

    • Model No.: Storm-0211

    • Transportation: Ocean,Land,Air

    Storm Circuit is a professional PCB and PCBA manufacturer in China we focus on high mix low to medium volume PCB fabrication and PCB assembly service for many years We can offer 0 2mm ENEPIG Rigid PCB 2 layer ENEPIG PCB 4 layer ENEPIG PCB 4mil trace and space PCB PCB features 1 Layer 2 2 Material FR4 3 Thickness 0 2mm...

    Contact Now

  • 4 layer RO4350B ENEPIG PCB

    4 layer RO4350B ENEPIG PCB

    • Model No.: Storm-0203

    • Transportation: Ocean,Land,Air

    Storm Circuit is a professional PCB and PCBA manufacturer in China we focus on high mix low to medium volume PCB fabrication and PCB assembly service for many years We can offer full turnkey service job including PCB Components Program Testing We purchase components from Digikey Mouser RS and so on So pls don t doubt...

    Contact Now

  • 4 layer 0.8mm ENEPIG PCB

    4 layer 0.8mm ENEPIG PCB

    • Model No.: Storm-0199

    • Transportation: Ocean,Air

    Storm Circuit is a professional PCB and PCBA manufacturer in China we focus on high mix low to medium volume PCB fabrication and PCB assembly service for many years We can offer full turnkey service job including PCB Components Program Testing We purchase components from Digikey Mouser RS and so on So pls don t doubt...

    Contact Now

  • 0.2mm FR4 ENEPIG PCB

    0.2mm FR4 ENEPIG PCB

    • Model No.: Storm-0010

    • Transportation: Ocean,Land,Air

    what is ENEPIG ENEPIG Electroless Nickel Electroless Palladium Immersion Gold is a surface finish for Printed Circuit Boards ENEPIG works well with lead free and conventional eutectic solder alloys This is the best way for gold wire bonding We can offer Quick Turn ENEPIG PCB with low cost 0 2mm PCB will be ok Rigid 0...

    Contact Now

Review

Muffin De Costa

Jan 27, 2020 4

Received with thanks.
Rahul Dev

Jan 21, 2020 5

The Enepig Plating Specification manufacturer really is my taste. I will keep cooperation.
Mile Obradovic

Jan 14, 2020 5

I love this Enepig Plating Specification , and its price is competitive.
  • Related Information
We've been committed to offering easy,time-saving and money-saving one-stop purchasing support of consumer for Enepig Plating Specification , enepig plating specification , enepig plating thickness , Upon today we have customers from all over the world including USA, Russia, Spain, Italy, Singapore, Malaysia, Thailand, Poland, Iran and Iraq. The mission of our company is to provide the highest quality products with best price. We are looking forward to doing business with you!

Send Us a Message

We didn't put all products on website. If you can't find the product you're looking for, please contact us for more information.

Home

Phone

Skype

Inquiry