Communicate with Supplier? Supplier
Dartin Xin Mr. Dartin Xin
What can I do for you?
Chat Now Contact Supplier
Storm Circuit Technology Ltd
Home > News > Which Via Should I Choose? A Guide to Vias in PCB Design
Online Service
Dartin Xin

Mr. Dartin Xin

Leave a message
Contact Now

Which Via Should I Choose? A Guide to Vias in PCB Design

2019-08-09
How much do you really know about vias, one of the building blocks of PCB design?


Vias are a staple of PCB design. But before you can decide whether to utilize buried, blind, or through vias, you should understand what they actually are and what they do for your board.

This article will act as a guide to basic via information.

Via Basics

What Is a Via?

Vias are used to electrically and thermally join traces, pads, and polygons on different layers of a PCB. Vias are copper cylinders that are placed or formed in holes that have been drilled in a PCB.

What Is a Via Pad?

Vias require a minimum amount of copper on a layer for a proper connection so, in most instances, a via pad (circle of copper called an annular ring) is attached to the end of narrow traces to increase the material available for a connection.

What Is an Antipad?


Surrounding the via pad is an area without copper known as the [antipad", which insulates the pad from surrounding copper.

How Are Vias Made?

Unless you are at home with a DIY via rivet gun on a 2-layer board, vias are created during the PCB manufacture process.

Briefly, holes are drilled through copper pads on the PCB, a chemical is put in the hole to dissolve epoxy on the internal layers to further expose the interior layer copper pads. Finally, a bit of copper is put in the hole with electroplating.

For an animation of how boards are made (including vias), see this video:


Most PCB manufacturers will put sacrificial vias on their PCBs on a section of the production board. The vias are then sliced, and the cross-sections are examined to determine the effectiveness of the electroplating process.


For parts of your circuit carrying power, or fast signals, use multiple vias to connect layer to layer. It is generally better to have several smaller vias than one large via. The design choice reduces inductance and provides additional paths for current in case one of the vias fails.

Types of Via

There are three basic kinds of vias:

  • Blind vias: connect an exterior layer to an interior layer
  • Buried vias: connect two interior layers
  • Through vias: connect two exterior layers

For a simple two-layer board, your only option is a through via. For boards with more than two layers, you might also be able to specify blind or buried vias in your design (at increased cost).

It is often the case that a via needs to form an electrical connection between internal and external layers. The use of a through-hole via in such situations places an unused hole (and possibly an unused pad) onto other layers, and this consumes PCB real estate and interferes with routing on adjacent layers, but it is the cheapest and most reliable option. Blind vias can free up real estate by creating a connection between the two layers and a hole only on the layers in between. Buried vias are not often used due to expense, reliability concerns, and difficulty of troubleshooting.


What Kind Should I Use?

Through vias are generally the least expensive via type to include on your design. Blind and buried vias should be discussed with your manufacturer prior to board layout to determine their capabilities.

How Do I Use Blind and Buried Vias in My Design?

It`s important to remember that when PCBs are manufactured, each layer consists of two sheets of copper separated by a dielectric core.


These layers can be assembled in a variety of fashions during manufacture, allowing a combination of blind buried vias. Your computer software likely will allow you to specify which layers you would like to connect, but it most will not stop you from making choices that cannot be manufactured. If you cannot recreate your stackup with cardboard and a stapler, without bending or tearing the cardboard, your PCB manufacturer cannot make your board.

What Size Should Vias Be?

Check with your manufacturer for their minimum drill size and minimum annular ring for the manufacturing process they will use. Typical mechanical drills don`t go much lower than 12 mil in diameter without frequent breakage, so the manufacturer will increase the cost to account for broken drills. Annular rings don`t often go below 6 mil for standard processing. So the smallest via you would create has a 12-mil diameter hole, and a 24-mil diameter pad.



Previous: What is the difference between a Pad and a VIA?

Next: 16 layer PCB quick turn in 8 days

Home

Phone

Skype

Inquiry